Gas fireplace service
Sweep & inspection
Caps & crowns
Flue relining
Masonry repairLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Why East Flatbush Homeowners Choose Gelco Chimney Cleaning
Chimney Sweep East Flatbush provides independent Gelco chimney cleaning, inspection and repair in East Flatbush, NY. We service Gelco flexible liners, top-mount and multi-flue caps, liner adapter and tee kits, and top-sealing damper assemblies – and we tell you plainly whether the component you have needs a repair or a replacement. We are an independent provider. We are not affiliated with, authorized by, or acting as a dealer for Gelco, and we work with quality parts that fit the equipment rather than claiming to supply genuine factory parts.
Gelco components show up across East Flatbush rowhouse chimneys because they fit the offset flues this housing stock is full of. Our technicians have up to 12 years of experience reading how those parts age in brick stacks that have been through coal, oil, gas and back again. Call (844) 932-2112 and we will set up a visit.
Why Trust Chimney Sweep East Flatbush for Your Gelco Chimney Cleaning?
We work on Gelco chimney equipment every season, so the wear patterns are familiar before we climb the roof. A flexible liner’s corrugations pit first where condensate collects. A cap collar loosens at the band before the mesh ever fails. A top-sealing damper’s gasket hardens in place long before the cable gives out. Knowing where each part tends to fail shortens diagnosis and makes the repair honest.
Quality parts that fit the installed system are the standard, and we match sizing and rating to what is actually in your flue. Warranty-safe practice matters too: we service and repair what is there rather than cutting or adapting components in ways that could compromise how the system was built. Where a Gelco part is still available we match it. Where a component is discontinued, a correctly sized aftermarket equivalent is the honest substitute – we say so up front instead of pretending otherwise.
Our technicians have up to 12 years of experience, and the same standard applies whether you have a Gelco liner, a Gelco cap, a Gelco damper or a mix of brands put together by whoever came before. We diagnose and repair what is installed and give you a straight answer about it.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Common Gelco Chimney Cleaning Problems We Fix in East Flatbush
East Flatbush’s early-20th-century semis and rowhouses have brick chimneys built for coal and then oil, and many flues have since been retrofitted for gas. That history is what drives most of the Gelco component failures we see here.
- Flexible liner corrosion from a wet flue. When a gas appliance was retrofitted into a flue originally sized for solid fuel, the flue runs condensate-wet for much of the heating season. That moisture eats at the corrugations and seams of a flexible stainless liner, showing as pitting or rust-through near the top where the flue stays coolest. Left alone, the liner vents less predictably and the rust spreads down.
- Cap looseness at the collar. Top-mount and multi-flue caps take the full force of wind and freeze-thaw on an exposed roofline. The collar works loose, the screen mesh tears or drops out, and birds, squirrels and rain get straight into the flue. In attached rowhouse rows, a loose cap on one unit can let water down toward the shared chase next door.
- Adapter and tee snout leaks at the offset. An older brick stack shifts over time, and the offset joint is where a liner adapter or tee snout pulls loose. You get creosote or water staining at the joint, a faint smell in damp weather, and a draft that gets worse after rain. The fix is a proper reseat, not a smear of sealant over the gap.
- Top-sealing damper gaskets that harden and stick. The gasket on a top-sealing damper assembly hardens with age and the cable or linkage starts to bind. The damper no longer seats flat, so the flue stays open to cold air and to downdrafts. Sticking is usually the gasket or the cable path, and it can be repaired without replacing the whole assembly.
- Missing caps on old abandoned flues. Many East Flatbush chimneys originally served coal furnaces or oil boilers and now sit unused with deteriorated parging and no cap at all. Those flues grow mold in humid summers and become nesting spots for animals. Before anyone fires a flue like that up, it needs a proper evaluation – the flue may not be safe or legal to use as-is.
Our free-standing Level 2 Inspection covers exactly this: a full look at the flue, the cap, the liner joints and the damper, with a condition report you can act on.
Gelco Parts & Our Repair-vs-Replace Approach
Most Gelco calls come down to a decision: is this a repair or a replacement? We make that call from the inspection, not from a sales script. Gelco-specific liner, cap and damper parts are matched to the installed system where they are still available. Where a Gelco component has been discontinued, a quality aftermarket equivalent sized and rated correctly for your flue is the honest substitute, and we tell you that’s what it is.
If a liner has failed in multiple sections, or a cap is beyond repair, replacement beats patching. Spot repairs make sense for a single defect – a loose collar, a small seam, a tired gasket – but a patch over a failed liner is a short-term fix that will not hold. That’s the one kind of job we don’t do.
Call (844) 932-2112 to book an inspection and get a straight answer on repair or replace. Estimates are free.
Our Gelco Service Process – Step by Step
- 1
Diagnosis. We start with a Level 2 Inspection of the flue, cap, liner joints and damper – looking at the Gelco components where they actually fail, at the corrugations, the collar, the offset joint and the gasket seat. We document what we find with photos so you can see it yourself.
- 2
Repair or install. If a collar needs reseating or a gasket needs replacing, we do the repair. If a liner has failed through, we replace it with the correctly sized and rated component. Where a Gelco part is unavailable, we use a quality equivalent and say so.
- 3
Test. We check draft, damper seating, cap fit and joint seals before we leave – not just whether it looks right from the ground.
- 4
Warranty-safe handover. We leave you the condition report and a plain explanation of what was done, so the next sweep or inspection has a record to work from. Nothing is recommended without the evidence to back it up.
See the difference
Before
After
Before
After
Before
AfterGelco Products We Service & Install in East Flatbush
We service the kinds of Gelco chimney components found in East Flatbush rowhouses and semis: flexible stainless chimney liner systems, top-mount and multi-flue stainless caps, liner adapter and tee kits that handle a flue offset, and top-sealing and universal damper assemblies. On the maintenance side, that means annual sweeps, cap replacement when a collar or screen has failed, and damper repair when the gasket or cable sticks. If a component needs attention before heating season, late summer and fall are when the crunch hits – book ahead. A typical rowhouse job starts with water staining on a ceiling or a draft that worsens after rain, traces it to a loose cap or a liner defect, and finishes with the flue swept, documented and sound.
We Also Service These Brands
Gelco is one of six professional chimney-industry brands we work with. We also service DuraFlex flexible liner systems and HeatShield liner resurfacing, alongside Olympia Chimney, Famco and Copperfield products. That matters when your chimney has more than one make in it – which is common in older East Flatbush houses – because we can service the whole system rather than turning away the part that isn’t Gelco.
FAQs – Gelco Chimney Cleaning Service in East Flatbush
No. We are an independent service provider, not affiliated with, authorized by or acting as a dealer for Gelco. We service and repair Gelco components with quality parts that fit the installed system.
Yes. We match Gelco-specific liner, cap and damper parts to the installed system where they are still available. Where a Gelco component has been discontinued, we use a quality aftermarket equivalent sized and rated correctly for your flue and tell you plainly that’s what it is.
Most Gelco cap reseats, damper repairs and annual sweeps are done in a single visit. A liner replacement takes longer and depends on the flue configuration. We give you the scope and the estimate before any work starts, and the written estimate sets the final price.
Flexible stainless chimney liner systems, top-mount and multi-flue stainless caps, liner adapter and tee kits, and top-sealing and universal damper assemblies. If you’re not sure what’s installed, we can tell you on inspection.
Servicing the installed system with correctly sized, properly rated parts is designed to keep it working as built. We don’t cut or adapt components in ways that could compromise the system, and we document what we do. Check your manufacturer’s warranty terms for specifics.
Pricing depends on the service – an annual sweep, a cap replacement, a damper repair or a liner replacement – so we give a per-job written estimate after inspection. The estimate is free, and that written price is what you pay. Call (844) 932-2112 for an exact quote.
It depends on how much of the liner has failed. A single defect at a seam or corrugation near the top can sometimes be repaired, but a liner that has failed through in multiple sections needs to come out. We make that call on inspection, with photos you can see. Call (844) 932-2112 and we’ll take a look.
Usually wind and freeze-thaw working at the collar band over several seasons, sometimes combined with a cap that wasn’t sized right to the flue. Reseating or replacing the cap with the correct fit is the fix. Estimate it with a call to (844) 932-2112.
Usually yes, if the assembly is sound underneath. Sticking is most often a hardened gasket or a binding cable, both of which are repair jobs rather than a reason to replace the whole damper. We’ll tell you which on inspection. Call (844) 932-2112 to book.
Not without checking. A liner sized for a gas insert is often too small in diameter for a wood-burning appliance, and going back to wood in an undersized flue is a draft and safety problem. The flue needs to be evaluated and, in most cases, the right liner sized for the appliance. Call (844) 932-2112 for an inspection before you fire it up.
Once a year for a wood-burning flue, and more often if you burn heavily or the liner has shown corrosion. Have it inspected before heating season – late summer into fall is the crunch here. Call (844) 932-2112 to book a sweep and inspection.
Book Your Gelco Service in East Flatbush, NY
If you have a Gelco liner, cap or damper that needs attention, call (844) 932-2112 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. We’ll inspect the flue, show you what we find and tell you plainly what it needs.
Written by the team at Chimney Sweep East Flatbush.