Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Fast, Reliable Chimney Cap & Crown Across Mill Basin
If your chimney cap is rusting through or your crown has hairline cracks, we can help. Chimney Sweep East Flatbush installs, replaces, and repairs caps and crowns for homeowners across Mill Basin, and we know this neighborhood’s chimneys well: the low brick houses off Strickland Avenue and down by the inlet, the two-flue setups on the older streets near National Drive, the flat and low-pitched roofs that catch bay wind. We serve Mill Basin directly and can reach Bergen Beach, Marine Park, and the surrounding blocks without a long wait. Caps and crowns are the first line of defense against water, and on a coastal chimney that defense matters. Call (844) 932-2112 to book a free estimate.
Why Mill Basin Homeowners Call Chimney Sweep East Flatbush for Chimney Cap & Crown
Mill Basin homes sit on filled marshland at the mouth of Jamaica Bay, and that changes what goes wrong up on the roof. Salt-laden nor’easters hammer the chimneys here in a way they don’t a mile inland in Flatlands or Marine Park, corroding galvanised caps, rusting dampers, and cracking crowns faster than most homeowners expect. We work with the same professional-grade materials certified chimney specialists rely on nationwide, so a replacement cap or a repaired crown is built to hold up against the bay air, not just until the next storm.
Local knowledge is what makes a cap and crown job go well. A technician who knows Mill Basin knows to look past the rusted cap and check whether the flue behind it was ever lined – a lot of these 1950s and ’60s boiler flues weren’t. We tell you exactly what we find and what it means before any work begins, and a chimney inspection is a safety document, not just a formality. Reglazing a cap onto an unlined flue without checking is how a small repair turns into a real problem. Our technicians have up to 12 years of experience with exactly this kind of coastal masonry chimney.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Our Chimney Cap & Crown Services in Mill Basin
Every cap and crown job here starts with a look at the whole chimney, because the salt air doesn’t fail in one place. Here’s what we handle most in Mill Basin.
Cap Installation
A properly fitted cap keeps rain and animals out of the flue while letting exhaust escape. We size and fit stainless caps on Mill Basin chimneys using Gelco and Famco components, so the fit is right at the job site rather than ordered and rescheduled. On a coastal chimney, stainless is worth the extra cost over galvanised – it won’t rust through in a few years of Jamaica Bay salt spray.

Cap Replacement
When a cap is rusted through or loose, replacement is usually straightforward. Many Mill Basin caps were put up decades ago with galvanised steel that has finally given out, and the flue underneath is fine. We check that before recommending anything, swap the cap, and confirm the new one is seated and sealed.

Crown Repair
The crown is the concrete cap on top of the chimney itself, and it’s where freeze-thaw cycles do their damage. Original concrete crowns on Mill Basin houses crack as water gets into hairline fissures and expands in winter. We repair crowns that are sound enough to save and pour new ones where the old crown is beyond patching, using materials sized to the chimney.

Crown Coating
Not every crown needs to be rebuilt. When the concrete is largely intact but showing surface cracking and spalling from the sea air, a crown coating seals it and slows further decay. It’s a smaller job with a smaller price, and we’ll tell you plainly when coating will hold versus when a repair makes more sense.
Multi-flue caps and custom caps round out the line, and you can see everything we offer on our chimney cap & crown page.
Trusted Brands We Service in Mill Basin
We work with six professional chimney-industry brands, and the ones you’ll hear about most on a cap or crown job are Gelco, Famco, Olympia Chimney, and Copperfield for caps and crowns, with DuraFlex and HeatShield for the liner work a cap inspection sometimes uncovers. These are the same materials certified chimney specialists rely on nationwide, not hardware-store substitutes. We don’t claim to stock parts in a local warehouse – that wouldn’t be honest – but we fit caps from standard industry lines and keep the turnaround quick, so a rusted cap doesn’t sit as an open hole on your roof for weeks. If something needs to be ordered, we’ll tell you the timeline up front.
See the difference
Before
After
Before
After
Before
AfterCommon Chimney Cap & Crown Problems We See in Mill Basin Homes
The pattern of failure out here is fairly consistent. Water almost always gets in before creosote shows up.
- Galvanised caps rusted through. Salt spray off the bay eats galvanised steel faster here than inland, and a cap that looks fine from the ground can be failing up close. Stainless is the durable fix.
- Cracked concrete crowns. Winter freeze-thaw cycles split original crowns, and water then wicks down onto terra-cotta flue tiles that have often already spalled with age.
- Unlined 1950s and ’60s boiler flues. Many Mill Basin houses vent a converted mechanical system through a flue that was never lined. Replacing the cap alone won’t correct the draft and safety issues – a liner assessment comes first.
- Spalled brick and rusted dampers. The same damp bay air that rusts dampers spalls brick faces above the roofline, so cap, crown, and masonry get checked together.
Pricing for Chimney Cap & Crown in Mill Basin, NY
Pricing is set per job by a free written estimate, but here’s how the numbers usually land in Mill Basin’s market. A cap installation typically runs $250 – $600, with stainless at the higher end and multi-flue or custom caps above that. Cap replacement is often $200 – $500 depending on access and size. Crown repair runs $400 – $900, and a full crown rebuild can reach $900 – $1,500. Crown coating is the smaller spend, typically $300 – $650. What moves the price is the pitch of the roof, how many flues you have, and whether the inspection turns up a liner that needs attention. We agree the flat price before booking, and estimates are free.
We Also Serve Cities Near Mill Basin
Not every chimney is right on the water, and the failure pattern shifts as you move inland. We work throughout Mill Basin and also cover nearby Bergen Beach, Marine Park, Flatlands, and Canarsie, where the same age of brick house often holds up a little longer against salt but still needs cap and crown work on the same schedule. Wherever you are on this side of Brooklyn, we can take a look and tell you what’s actually failing.
Serving Mill Basin, NY – Our Local Coverage Area
We serve Mill Basin and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
FAQs – Chimney Cap & Crown in Mill Basin
Mill Basin sits on filled marshland at the mouth of Jamaica Bay, so caps and crowns take salt-laden nor’easter wind head-on in a way chimneys a mile inland in Flatlands or Marine Park do not. Salt spray corrodes galvanised steel and speeds the rusting of dampers, so a galvanised cap that would last inland gives out sooner here. Stainless components hold up far better against that exposure. Call (844) 932-2112 for a free estimate on a stainless replacement.
Likely yes, or at least an inspection to confirm it. Many 1950s and ’60s Mill Basin boiler flues were built unlined, and without a proper liner the exhaust gases and moisture degrade the chimney from the inside – a cap alone won’t fix the draft and safety issues underneath it. A Level 2 inspection tells you whether HeatShield resurfacing or a full DuraFlex liner is the right call before the cap goes on. Call (844) 932-2112 and we’ll look first.
Annual inspection is the right interval here, and the coastal exposure is the reason. Salt spray and freeze-thaw cycles crack crowns and rust caps faster than inland, so a yearly look catches a failing cap or a hairline crown crack before water gets down into the flue. A standalone inspection gives you a clear condition report you can act on. Call (844) 932-2112 to book one.
Crown repair fixes or rebuilds damaged concrete; crown coating seals a crown that’s mostly sound but showing surface cracking and spalling from the sea air. Coating is the smaller spend and works when the concrete is intact underneath; if the crown is split through, a repair or rebuild is what actually stops the water. We’ll tell you which your Mill Basin chimney needs after we see it. Call (844) 932-2112 for a free estimate.
Yes. Many Mill Basin houses have two flues – a boiler flue and a fireplace flue – and a multi-flue cap covers both in one unit, sized to fit the chimney top. It’s often the cleaner solution than two separate caps and gives better protection for both openings. We fit these from Gelco and Famco components so the sizing is right on site. Call (844) 932-2112 to talk through your setup.
Call (844) 932-2112 for a free estimate on chimney cap and crown work in Mill Basin. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Chimney Sweep East Flatbush.